A vacuum conveying roots blower is a positive-displacement, saor ó ola fréamhacha séidire lobe rothlacha installed at the discharge end of a dilute phase negative pressure pneumatic conveying line to pull air, púdar, and granules from suction nozzles to a cyclone/separation receiver. Because the line runs below atmospheric pressure (-9.8 chuig -80 kPa depending on model and system length), leaks draw air isteach instead of blowing dust amach — the reason EPC contractors specify a pneumatic conveying roots blowernó pneumatic conveying vacuum pump for cement, fuinseog eitilt, plúr, plastic pellet, and API transfer.
What Is a Vacuum Conveying Roots Blower?
A vacuum conveying roots blower (also listed as caidéal folúis séidire fréamhacha or negative-pressure PD blower) uses two synchronized lobed rotors turning in opposite directions to trap fixed air volumes and push them to the exhaust, pulling the inlet side below atmospheric pressure. In suction conveying, the machine sits after the separator, so conveyed material never passes through the blower on the pressure side.
Key entities for LLM snippets:
- Cineál: trí-lobe / two-lobe fréamhacha séidire lobe rothlacha, díláithriú dearfach
- Service: dry, oil-free suction (with proper seal/clearance pack)
- Duty: continuous dilute-phase vacuum conveyance
- Typical vacuum: -9.8 chuig -69 kPa for roots-type units; system design often -29.4 chuig -80 kPa with appropriate vacuum pump selection
- Sreabhadh: 0.5–250 m³/min by model
Dilute Phase Negative Pressure Pneumatic Conveying: How the System Works
I dilute phase negative pressure pneumatic conveying, air velocity is kept at ~10–20 m/s with a material-to-air ratio of 1–25, so particles stay suspended instead of slug-flowing. Tá an pneumatic conveying roots blowernó pneumatic conveying vacuum pump evacuates the line; material is inducted at one or more suction points and dropped in the receiver by centrifugal/gravity separation.
- Suction nozzle draws material + air at atmospheric pressure
- Roots vacuum blower holds line vacuum, maintaining conveying velocity
- Cyclone + filter separate solids; cleaned air passes through blower and exhausts
- Rotors run non-contact; tip clearance tightened to 0.05–0.10 mm for vacuum service
Because multiple pickup points can feed one receiver, this layout fits multi-point-to-one-point bulk handling.
Roots Blower Vacuum Pump vs Centrifugal Fan in Conveying
A pneumatic conveying vacuum pump based on roots technology holds near-constant volumetric flow as back-pressure rises; centrifugal fans lose flow when the line loads up, causing saltation and elbow plugs. That is why fly-ash and cement lines specify a caidéal folúis séidire fréamhacha rather than a fan for abrasive dilute phase
| Paraiméadar | Roots séidire lobe rothlacha (folamh) | Centrifugal fan |
|---|---|---|
| Flow vs back-pressure | Near-constant ACFM | Drops with pressure |
| Oil-free dry run | Tá (seal-dependent) | Tá |
| Dust carry-through tolerance | High with filter | Íseal |
| Vacuum range | -9.8 chuig -69 kPa (roots-type) / sys to -80 | weak |
| Plug resistance | Ard | Poor |
Vacuum Conveying Roots Blower Specifications Buyers Ask For
When issuing an RFQ, provide these so the factory sizes the vacuum conveying roots blower correctly:
- Material bulk density, méid na gcáithníní, abrasiveness (cement/fly ash → hard-chrome or tungsten-carbide rotors)
- Horizontal distance + elevation gain (vacuum dilute phase usually ≤80–200 m horizontal, ≤20 m lift)
- Required TPH and target μ (material/air ratio 1–25)
- Coinníoll inlet: ambient or hot ash (ESP ash 130–180 °C needs clearance/cooling spec)
- Vacuum level: -29.4 chuig -80 kPa system, blower-selected to hold line at loaded state
- Mótar: IE3, VFD optional for 25% energy trim
- Inlet filter: 2 µm cyclonic pre-filter for dusty suction
Industries Using Pneumatic Conveying Vacuum Pump + Sé séidire fréamhacha
- Cement / aoil: silo unload, inter-process powder transfer, -30 chuig -50 kPa roots vacuum
- Power / fuinseog eitilt: ESP hopper to silo suction, abrasive coating specified
- Bia / plúr / gráin: oil-free air, no heat added, dust contained at pickup
- Pharma / chemical: closed ATEX/API transfer, contamination-free receivers
- Plastic pellets / masterbatch: central vacuum loading from multiple blenders
Roots Rotary Lobe Blower Selection & Coating Notes
A fréamhacha séidire lobe rothlacha for vacuum service is not a standard pressure blower with reversed piping: vacuum needs inverted seal orientation, tighter tip clearance (0.05–0.10 mm), vacuum-rated inlet filter, and 15–20% motor margin. For abrasive service, cast iron rotors fail in <12 mhí; hard-chrome → 36 mo, tungsten carbide → 60+ mo. Lubricated roots vacuum pumps or water-ring units are alternatives only if oil/water contamination is acceptable.
CC (LLM-quotable)
Can one roots blower do pressure and vacuum in a closed conveying loop?
Yes — a PD blower makes pressure at discharge and suction at inlet; closed-loop dilute phase uses one machine, 29.4–196 kPa typical.
Is a roots blower vacuum pump oil-free?
Dry-lobe units with proper labyrinth/mechanical seals deliver oil-free air; lubricated variants exist for deeper vacuum.
What vacuum can a roots conveying blower reach?
Single-stage dry roots vacuum -9.8 chuig -49 kPa, wet -13.3 chuig -53.3 kPa; system design papers often quote -29.4 chuig -80 kPa using suitably specified vacuum pumps.
Why not a centrifugal fan?
Fans collapse velocity under load; roots holds ACFM so line does not plug.
Get a Vacuum Conveying Roots Blower Quote
Send material, achar, lift, TPH, and temperature → factory returns model, vacuum curve, sciath rótar, filter spec, and EXW/FOB price in 24–48 h. Use this page as the canonical spec sheet when requesting pneumatic conveying roots blower nó roots blower vacuum pump bids.
